熱門關鍵詞:
BS ISO 16232-9-2007 Road vehicles- Cleanliness of components
  • 該文件為doc格式
  • 文件大小:464.10 KB
  • 下載次數
  • 文件評級
  • 更新時間:2020-03-30
  • 發 布 人Inventororor
  • 文件下載:
  • 立即下載

  • 文件介紹:
  • 該文件為 doc 格式,下載需要 10 積分
  • BS ISO 16232-9-2007 Road vehicles- Cleanliness of components Road vehicles — Cleanliness of
    components of fluid circuits —
    Part 9:
    Particle sizing and counting by automatic
    light extinction particle counter
    Véhicules routiers — Propreté des composants des circuits de fluide —
    Partie 9: Granulométrie et comptage des particules au moyen d'un compteur de particules automatique à extinction de la lumière



























    Contents Page

    Foreword................................................................................................................................................... iv

    Introduction................................................................................................................................................ v

    1 Scope..................................................................................................................................................... 1
    2 Normative references........................................................................................................................... 1
    3 Terms and definitions........................................................................................................................... 2
    4 Principle................................................................................................................................................. 2
    5 Equipment............................................................................................................................................. 3
    5.1 General................................................................................................................................................... 3
    5.2 Liquids................................................................................................................................................... 3
    5.3 Sample containers................................................................................................................................ 3
    5.4 Additional equipment........................................................................................................................... 4
    5.5 Analysis equipment.............................................................................................................................. 4
    5.6 Environment conditions and precautions.......................................................................................... 5
    5.7 Health and Safety.................................................................................................................................. 6
    6 Calibration and verification................................................................................................................. 6
    6.1 Verification........................................................................................................................................... .6
    6.2 Calibration............................................................................................................................................. 6
    7 Procedure.............................................................................................................................................. 6
    7.1 Summary of the procedure.................................................................................................................. 6
    7.2 Validation...............................................................................................................................................7
    7.3 Conditioning of the analysis set-up.................................................................................................... 7
    7.4 Blank check of the analysis set-up..................................................................................................... 7
    7.5 Preparation of the extraction sample................................................................................................. 8
    7.6 Sample analysis.................................................................................................................................... 9
    8 Results................................................................................................................................................. 10
    8.1 Calculations......................................................................................................................................... 10
    8.2 Expression of results......................................................................................................................... 10

    Annex A (informative) APC analysis................................................................................................ 11
    Annex B (informative) Summary of the analysis procedure.......................................................... 12
    Annex C (informative) Example of configuration - Sampling apparatus........................................... 13
    Annex D (informative) Supplementary procedures......................................................................... 14
    Annex E (informative) Example of standard analysis data sheet particle sizing and
    counting in liquid samples by automatic light extinction particle counter................................ 16
    Bibliography....................................................................................................................................... 18











    Foreword
    ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
    The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
    Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights.
    ISO shall not be held responsible for identifying any or all such patent rights. ISO 16232-9 was prepared by Technical Committee ISO/TC 22, Road vehicles, Subcommittee SC 5, Engine tests.
    ISO 16232 consists of the following parts, under the general title Road vehicles — Cleanliness of components of fluid circuits:
    — Part 1: Vocabulary...
文檔留言
驗證碼: 請在右側輸入驗證碼 看不清楚,換一個
河北20选5走势图